Capacitive sensor flex circuit: electrodes, shields and tanks.
- A 2-layer flex with copper electrodes on one layer and an active shield on the other can read liquid level through a plastic tank wall.
- The shield is driven with the electrode signal, not grounded, so it blocks noise from behind without loading the sensor.
- Most field problems come from the bond, not the copper: an air gap under the electrode shifts the reading.
A capacitive sensor flex circuit is a thin polyimide circuit carrying copper electrodes that detect a change in capacitance, from a finger, a lid or a liquid behind a wall. For level sensing, it is bonded to the outside of a tank, with an active shield layer behind the electrodes so only the tank side is sensed.
The flex is the sensor.
There is no probe in the liquid, no seal to leak and no part to clean, which is why appliance makers use it on water and milk tanks.
How does a flex PCB sense liquid level through a wall?
Water has a far higher permittivity than air or plastic. When liquid rises behind an electrode, the electrode’s capacitance to its surroundings rises with it. A capacitance-to-digital controller on the main board reads that change, and firmware turns it into a level or a set of switch points.
Two layouts are common. Separate pads at set heights give discrete points, such as empty, low and full. One long electrode beside a short reference electrode, always covered, gives a continuous level, with the reference cancelling changes in liquid type and temperature.
What does an active shield do?
It stops the electrode sensing anything except the tank. The shield is a copper area on the second layer, behind the electrode and its feed trace, driven by the controller with a copy of the electrode signal. With no voltage between electrode and shield, no field forms between them.
| Behind the electrode | Effect on the reading | When to use it |
|---|---|---|
| Nothing | Senses both sides, including hands and housing | Rarely; only in open, fixed set-ups |
| Ground plane | Blocks the back but adds heavy parasitic capacitance | Touch keys with strong signal to spare |
| Active shield | Blocks the back without loading the electrode | Level sensing and other weak signals |
Hatched copper is the usual shield pattern. It shields well, adds less capacitance than a solid pour and keeps the flex supple enough to follow a curved tank. On our double-sided flex circuits, the shield runs under the feed traces as well as the pads, because an unshielded trace is a sensor too.
How should the electrodes and traces be laid out?
- Size the pads to the change you need to see. A bigger electrode gives more signal, but also more noise pickup if it is not shielded.
- Keep feed traces narrow and shielded. Route them away from the liquid edge, with the shield underneath along their full length.
- Separate tanks. Where one flex serves several tanks, space the electrodes apart and give each its own feed and shield so one tank does not read another.
- Keep ground away from the sensing face. Ground copper near an electrode competes with the liquid for its field.
Shielding against outside interference is a related but different job, set out in our guide to flex PCB EMI shielding.
How is a sensor flex bonded to the tank?
With a pressure-sensitive adhesive laminated across the whole electrode area at the factory, so the line only peels and presses. The bond matters more than any copper detail. An air bubble or a lifted edge replaces high-permittivity plastic with air, and the reading drifts from unit to unit.
Keep the electrode area flat and free of stiffeners. Put the stiffener only at the connector tail, where a ZIF or board-to-board connector needs a firm, flat end. An ENIG finish on the contact fingers gives a flat, solderable surface that resists corrosion in humid appliance interiors.
What else in an appliance runs on the same flex?
Level electrodes rarely travel alone. The same product often carries a Hall-sensor flex that detects a lid magnet, a chamber flex with a temperature sensor, and a camera extension. Using one flex supplier, one stack-up family and one finish across all of them simplifies qualification. Typical uses are listed in our flexible PCB applications guide.
From our flex line: When a level sensor reads differently from unit to unit, we check the adhesive lamination before the copper. More often than not, the electrode is fine and the bond is not flat.
What this guide does not cover
Electrode sizes, shield hatch ratios and switch thresholds depend on the tank wall, the liquid and the controller chosen. We build the flex to your layout and test it for continuity and isolation; capacitance calibration belongs to the controller design and is confirmed on the assembled product.
Can a flex PCB measure liquid level through a tank wall?
What is an active shield on a capacitive sensor flex?
Should the shield layer be solid or hatched copper?
How many layers does a capacitive level sensor flex need?
How is a sensor flex fixed to the tank?
Designing sensor flexes for an appliance?
Send the layouts for each flex and your annual volume. We check stack-up, shield and adhesive and reply in two working days.


