Resources / Backlit keypad flex circuit case study
Case study

A backlit keypad flex circuit, 252 parts in 22 days.

  • An equipment customer needed a keypad whose circuit layer was a 0.125 mm copper flex carrying 13 green 0603 LEDs, metal domes and a 10-pin ZIF tail.
  • Artwork was approved one day after the order. The customer skipped sample validation and asked for 252 production parts before a fixed date.
  • The lot passed outgoing QC on day 21 and shipped on day 22, ahead of the deadline.

A backlit keypad flex circuit is the copper circuit layer inside a control keypad, with LEDs soldered onto it to light the keys. In this job we built one with 13 surface-mount LEDs and a ZIF tail, and shipped 252 production parts 22 days after the order.

The order arrived in August 2019 with a hard date attached. The customer’s own schedule left no room for a sample round.

So the job ran straight from approved artwork to a production lot.

What did the customer need?

The part was an operator keypad for a piece of equipment, an HMI panel with tactile keys and lit indicators. Under the printed overlay sat a stack of adhesives and spacers, and under those the part that did the electrical work: a 0.125 mm flex circuit.

That flex carried three jobs at once. It held the contact pads under each key, it carried 13 green LEDs in 0603 packages to light the panel, and it ended in a 10-pin tail that plugs into a ZIF connector on the main board.

Why a copper flex circuit and not printed silver?

Many simple keypads use a silver ink circuit printed on PET film. It is cheap and fine for switch contacts alone. This design had three features that point to etched copper instead.

  • Soldered LEDs. Copper takes solder paste and reflow like any board. Printed silver cannot be reflow soldered, so LEDs on PET are usually bonded with conductive epoxy.
  • Thirteen lit channels. Copper traces have far lower resistance than printed silver, which keeps LED drive consistent from the first key to the last.
  • A plug-in tail. A ZIF tail is inserted and removed during assembly and service. Copper under polyimide coverlay handles that better than printed ink.

Once LEDs are soldered onto the circuit layer, the keypad is really a small flex circuit assembly, and it is built and inspected like one.

What was in the stack?

The table lists the build as ordered, from the top face down. Material grades are as specified on the order.

LayerAs builtJob
OverlayMatt-finish graphic overlay filmPrinted legend, the face the operator touches
Overlay adhesive0.225 mm double-sided tapeBonds the overlay to the spacer
Spacer0.1 mm PET with adhesiveHolds the domes in position and sets the key gap
Tactile domes12.2 mm nickel-plated metal domesClick feel and contact closure
Circuit0.125 mm copper flex, 13 green 0603 LEDsSwitch pads, backlight and routing
Tail10-pin, for a ZIF connectorPlugs into the main board
Rear adhesive3M 467 transfer adhesiveMounts the keypad to the panel

The flex layer is a single-sided flex circuit in function: one copper layer, pads on the face that meets the domes, LEDs on the same face. Base film and copper choices are covered in FPC materials.

How did 252 parts ship in 22 days?

DayDate (2019)Step
07 AugustOrder released to production as a sample order
18 AugustCustomer approved the artwork
18 AugustCustomer waived sample validation and asked for 252 parts before 4 September
2128 AugustAll 252 parts passed outgoing QC inspection
2229 AugustLot shipped

Two things made the date possible. The artwork loop closed in one day, because the drawing arrived complete, with the stack, dome, LED and connector already named. Once artwork was fixed, the flex circuit and the laminated layers could be prepared in parallel.

Our normal flow starts production from an approved sample. Here the customer chose to skip that step to protect its own schedule. That moves the first-article risk onto the production lot, so the full 252 went through outgoing inspection before release.

From our flex line: When a customer waives samples, the artwork approval has to carry the weight a sample normally would. Before signing off, check LED positions against the overlay windows and the tail pin order. Those are the two errors a sample would have caught and a production lot cannot fix.

What does LED assembly on a keypad flex need to get right?

  • LED position against the overlay. Each LED has to sit under its window or legend, with the spacer cut clear around it.
  • Clearance from the domes. Solder joints and LED bodies stand proud of the circuit, so they must stay out of the dome footprint and the key travel.
  • Polarity and colour. Thirteen identical LEDs are easy to place reversed. Orientation marks on the flex and a light-up check at inspection catch it.
  • Tail thickness. A ZIF connector specifies the thickness it grips. Thin flex tails often need a polyimide stiffener to reach it, checked against the connector datasheet.

What this case does not show

The record ends at shipment. We have no field data from the customer, no brightness uniformity measurements, and no life cycle results for the keys. We also cannot say whether the customer later reordered from this lot.

The customer’s name, part number and panel artwork are left out. Material grades are given because they are standard catalogue parts.

When should a keypad use a copper flex circuit?

If the keypad hasCircuit layerWhy
Switch contacts only, low cost targetPrinted silver on PETCheapest, enough for contacts alone
Soldered LEDs, resistors or connectorsCopper flex circuitReflow-solderable, low resistance
A ZIF tail or fine-pitch connectorCopper flex circuitDurable, precise tail for repeated mating

Where the only question is resistance, printed silver can still win; the copper flex vs printed silver case study shows a 30 ohm limit met without copper. Another worked example from our flex line is the pouch cell flex circuit case study, a dual-access battery part reviewed at quote stage.

What is a backlit keypad flex circuit?
The copper circuit layer inside a keypad, carrying the switch pads under each key and the LEDs that light the keys or indicators. It usually ends in a tail that plugs into the main board.
Can LEDs be soldered onto a printed silver keypad circuit?
Not by reflow. Printed silver ink does not take solder, so LEDs on PET circuits are usually bonded with conductive epoxy. A copper flex circuit takes standard SMT reflow.
How fast can a keypad flex circuit ship?
It depends on how complete the drawing is. In this case artwork was approved in one day and 252 production parts shipped 22 days after the order.
Do ZIF tails on thin flex need a stiffener?
Often. A ZIF connector grips a set thickness, and a thin flex tail may need a polyimide stiffener to reach it. Check the connector datasheet before the drawing is frozen.

Building a lit keypad or control panel?

Send your stack drawing, LED list and connector part number. We confirm the flex build and lead time in two working days.